important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to Assemble a New Bike

Overview of a boxed bike assembly. Shows how to put together a mail-order bike.

These days you can get a great deal on a new bike by ordering online. Today we’ll learn how to properly assemble a mail order bike right out of the box. Since there are so many different types of bikes and components available, I’ll give a brief overview of the assembly. If you’re watching this video on bikeride.com, you can check the links in the text below for more specific instructions.

Tools

For this job you’ll need several tools. Ideally you should have a repair stand and a wheel truing stand. Other necessary tools include wire cutters, a set of metric allen keys, a set of metric open-end wrenches, flathead (-) and phillips (+) screwdrivers, cone wrenches, a pedal wrench and an air pump. You’ll also need some waterproof grease, chain oil and a rag.

Unpacking

Open the top flap and carefully pull everything out of the box. Apply some grease to the inside of the seat tube, slide the seatpost in to the minimum insertion mark, grease the threads of the seatpost bolt and tighten it just enough so it will hold the weight of the bike. Then clamp the seatpost in your repair stand.

Remove the front wheel by using wire cutters to carefully snip the zip ties. To save these for future use, cut them just before the head and then pull out and recycle the remaining piece of zip-tie. This leaves you with a short piece of zip-tie that can be used again for odd jobs. Remove the rest of the packaging and either recycle it, or save it so you can box your bike up in the future.

Assembly

If your headset and bottom bracket have loose ball bearings, open them up and check for grease and adjust as needed. If you have sealed cartridge bearings in these places you can skip this step.

Now we’re ready to install the handlebar. Grease all of the stem bolt threads and shaft if you’re installing an older quill-style stem. Then center the handlebar and tighten the stem bolts evenly so the gap is equal on both sides. Tighten the top cap just enough to hold it in place.

Remove the rear wheel and cassette or freewheel, and open the hubs on both wheels to check for grease. Add more grease as needed and then adjust the hub cones so they spin freely with very little play. See the hub overhaul tutorial for adjustment instructions. Grease the cassette or freewheel’s threads before re-installing them.

Watch the wheel-truing tutorial to see how to de-stress and true the wheels. Then inflate the tires to the recommended pressure and install both wheels on the bike.

It’s a good idea to grease the threads of the crank bolts, chainring bolts, and other bolts that hold accessories like water bottle cages. This will help them repel water and dirt and stop them from seizing up. Grease the pedal threads and install them. Remember that the left pedal always has a reverse thread, so you have to tighten it by turning counter-clockwise.

Set up and adjust your brakes. See the brake tutorials page for set-up instructions on specific brake types. Then lube the chain and adjust the derailleurs. Watch the front and rear derailleur tutorials to see how.

Apply any stickers and/or accessories and then remove the bike from the stand. Adjust your seat height and angle, align your handlebars and adjust your headset. See the headsets and handlebars pages for related tutorials… and then get out for ride!

By Alex Ramon

A bicycle geek since early childhood, spent his twenties as a mechanic in bike shops. His passions include flatland BMX, unicycles, cycle touring, mountain biking and road riding.

Recommended Tools

Discuss this topic in the Bicycle Repairs and Mechanics Forum

suspicious broken part after service--is this legit?

Pros & Cons of presta valve vs schrader valves

70's=80's Free Spirit Blaze MTN

Front Disc screeching/vibration .. help please :-)

2nd hand rad rover repair help needed

Axle keeps slipping on applying force/climbing hills..

Need help with Drivetrain Update

Latest post 3 months ago

Hello everyone, I'm an older lifelong cyclist that recently had my beloved old yeti mountain bike stolen, and to try and fill that void, I picked up a 2015 Specialized Crosstrail (I'm riding more paved and gravel trails these days, my full-on mountain bike days are over!). The bike was in very good physical condition, apparently very lightly used. I was unable to ride before purchase, but it looke...

Velowave Ranger break change question

Latest post 3 months ago

Hello! I tried to change my Velowave ranger e-bike breaks and the lever would not have traction. I researched and learned I needed to bleed the breaks, I tried the top method with the cup with a break bleeding kit. Still had the same issue, I tried to use the syringe at the caliper but the hole was too small for any of the included adapters. Is it just trapped air in the calipers/line that is ca...

Eye to Eye Shock Lengths

Latest post 3 months ago

Will my conversion work? I have an old 2014 Giant Trance 1. It is a small frame. It is just a backup bike. It is still fun to ride and works well when a friend is or family member is visiting and bikeless. I hate sending things to the land fill or not being able to keep them repaired and running. I already replaced the fork a couple of years ago. I already found some parts and converted to a ...

Shimano law suit

Latest post 3 months ago

Remember the Shimano law suit? Fortunately I had the"good model series" Thousands of riders trusted these components without a second thought. Now, the story has taken a serious turn. Shimano has agreed to pay an $11.5 million penalty after US regulators found the company failed to report a major defect in its 11 speed road cranksets on time. According to the CPSC, Shimano had received thou...

Question regarding rear hub replacement for possible out of production bike?

Latest post 4 months ago

Hi there, I have a question in regards to either finding a replacement hub for my rear Mountain Bike or just replacing the whole wheel entirely. However when I went to a local bicycle shop (in China, that is so there are language barriers to keep in mind), upon inspection they claimed that the bicycle was too old to accept the replacement of their modern parts, which I honestly find hard to believ...

Need suntour derailleur replacement

Latest post 4 months ago

My sensation crossroads cruz needs a rear derailleur. I need to verify which shimano part and shifter will work. Thanks Bob...

Inner side tube punctures

Latest post 4 months ago

I haven't been riding a bike for about two years, before that I was riding it extensively for about 5 or more years. It is a 26 inch mountain bike (if that matters at all). The bike was just staying on flat tires for these two years. After i decided to put the bike to life again so to speak I started to get inner tube punctures (punctures on a tube from the inner side, the side not facing the road...

How to adjust shock preload?

Latest post 4 months ago

These are Noleen NR-1 shocks on an old Girvin ProFlex MTB. How do I get a grip on the preload adjuster? There is very little surface area & there are no notches for a typical spanner & a pipe wrench, vice grips, etc. which are sure to mar the springs if I can even get them in there to grip it. The working space on the fork shock is especially tight. See attachment photos. Thanks! ...