important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to True a Wheel

Aspects of wheel truing covered include radial, lateral, centering (or dishing) and spoke tension.

Wheel truing is a delicate procedure that requires time and patience. In this tutorial I’ll try and demonstrate the many aspects as clearly as possible. Ideally you’ll want to have a wheel truing stand, good lighting and a comfortable workspace.

Wheel Truing Tips

If you don’t have a truing stand, lateral, or side to side adjustments can be done using your brake pads as a guide. If truing the wheel on your bike, be sure to deflate the tire before you begin. For radial, or up and down adjustments, you can use an L-square as a guide by attaching it to your fork or frame.

It is very important to use the correct size spoke wrench to avoid stripping the spoke nipples.

Before you begin, carefully inspect your wheel for any bent or broken spokes. Make sure your hub bearings don’t have any play and then carefully squeeze a drop of light oil into all of your spoke holes.

Spoke nipples have a regular right-hand thread, but that while you’re truing a wheel, you will be looking at the nipple upside-down, so you have to turn the spoke wrench clockwise to loosen and counter-clockwise to tighten.

Make sure the spoke doesn’t turn with the nipple, which will cause it to twist and break. If it does turn, apply some light oil to the nipple threads and try again.

If a spoke does break while you’re truing, it’ll shoot out the spoke hole with great force, so be careful not to place your face in line with the rim. Safety glasses are highly recommended.

Radial (Vertical) Adjustments

To check radial alignment, place the guide near the highest point on the outer edge of your rim. Find the high spots in your rim by spinning the wheel and correct them by tightening both left and right side spokes evenly. Correct any low spots by equally loosening the spokes in the effected area.

Tighten or loosen spokes in 1/4 turn increments. For example, if the effected area spans the length of four spokes, tighten all four spokes 1/4 turn, and then tighten the middle two spokes another 1/4 turn. Then re-check the radial alignment and repeat the process as needed.

Lateral (Side to Side) Adjustments

To check lateral adjustment, place the guide close to the rim sidewall and look for high spots on either side. To correct a left or right high spot, tighten the spoke that leads to the opposing hub flange and equally loosen the spoke that leads to the hub flange on the same side as the high spot.

Just like radial adjustments, tighten or loosen the spokes in 1/4 increments. Again if the effected area spans four spokes, loosen and tighten all four spokes 1/4 turn, and then loosen and tighten the middle two spokes another 1/4 turn.

Re-check the lateral alignment and re-adjust as needed. Remember that on the rear wheel, the right side spokes have a lesser angle and effect lateral movement less than the left. The left side spokes have greater angle and effect radial alignment less than right. To compensate for this difference, the right side spokes should be adjusted two turns for every turn on left.

Centering (Dishing)

Rims should be exactly centered between the axle nuts. To check this you can use either a dishing tool, or your frame to check the measurement on each side.

If the rim is off-center, pull it in either direction by equally tightening all of the spokes on one side 1/4 turn, and loosening all of the spokes on the other. Then check the alignment again and repeat the process until the rim is centered.

Spoke Tension

To check spoke tension, pluck each spoke in the middle and listen to the sound. On the front wheel, all of the spokes should sound the same on both sides. On the rear wheel, each side should sound slightly different, but the spokes on each side should sound the same as each other.

Most people don’t have a spoke tensiometer, so it’s a good idea to compare the sound of your spokes to the sound of a wheel that you already know has proper tension. Remember that spoke changes effect the whole wheel, so you might have to repeat these steps several times before it is true.

Stress-Relieving Spokes

After the wheel is true you should always pre-stress the spokes and re-adjust before riding. Failure to do this could cause broken spokes later. There are two ways to do this. The first way is to squeeze together the parellel spokes on both sides of the wheel. The second method involves resting the wheel sideways on the floor and gently pushing down on both sides of the rim, all the way around the wheel in 1/8 increments.

After pre-stressing the spokes you will usually have to re-check and make some minor adjustments. If after stressing the wheel you notice that your rim is severly warped, it means that your spoke tension is too high. Loosen all of the spokes 1/2 turn and re-true the wheel.

By Alex Ramon

A bicycle geek since early childhood, spent his twenties as a mechanic in bike shops. His passions include flatland BMX, unicycles, cycle touring, mountain biking and road riding.

Recommended Tools

Discuss this topic in the Bicycle Repairs and Mechanics Forum

Need suntour derailleur replacement

Catastrophic bicycle failures

Pros & Cons of presta valve vs schrader valves

How to clean a bike for beginners (Foxter mtb 29er)

Freehub replacement sealed bearing wheel

Shimano RevoShift upgrade

Sram Transmission derailleur possibly dead?

Specialized bicycle post issue

Philodo H8 5000W

Axle keeps slipping on applying force/climbing hills..

suspicious broken part after service--is this legit?

Latest post 3 months ago

Hey all, I'd love some feedback on a repair issue. I just got the brakes bled and the first ride after was fine. But after one week of sitting idle, I took it out and the rear brake was suddenly making a horrible loud screeching noise when applied. Took it back to the shop and the mechanic showed how the two halves of the brake were not perfectly aligned and holding firm and there was oil leakage....

70's=80's Free Spirit Blaze MTN

Latest post 3 months ago

70's-80's Free Spirit Blaze MTN 2.JPG (Size: 21.86 KB / Downloads: 15) 3.JPG (Size: 33.89 KB / Downloads: 16) DSCN3722.JPG (Size: 32.65 KB / Downloads: 16) 4.JPG (Size: 56.63 KB / Downloads: 16) I need a front index shift lever or the matched set. Falcon derailleur, 10 speed or whatever is compatible. 7.3mm is the closet spacing measure...

Front Disc screeching/vibration .. help please :-)

Latest post 3 months ago

Front Disc brake(Shimano) makes dreadful noise/vibration just at the ‘bite’ point where it stop the wheel (final 2 or 3 cms of rotation on the rotor ! Only started a month ago No luck in sorting it ! .. have had pads, rotor and caliper all replaced and it makes very little difference (all are clean, aligned and functioning as they should) Absolutely no problem on the rear. Don’t know wh...

2nd hand rad rover repair help needed

Latest post 3 months ago

So I bought this second hand rad rover five power bike it worked for the whole day and the end of the day I thought it died on me but it hasn't been able to start back up please contact me if you think you could help I've done some research and I have no idea what I'm doing I just need some help somebody knows what they're doing to guide me with this please I spent all my money on this I don't hav...