How to Adjust Your Front Derailleur
Applies to most 3-chainring derailleur systems.
Today we’re going to learn how to adjust the front derailleur. Make sure that you’ve already set up your rear derailleur, as you will need to access all of your rear gears for this tutorial.
Front Derailleur Components
Height Adjustment
The first step is to adjust the derailleur’s height and angle using the positioning clamp that attaches the derailleur to your bike’s frame. This can be a bit tricky, since tightening the clamp’s bolt will set both height and angle at the same time. To make things easier, tighten the clamp so that it is secure, but loose enough to move it around with your hand.
For correct height adjustment, position the bottom of the derailleur cage as close to the largest sprocket teeth as possible, so that it still clears. Manufacturers recommend a 2mm spacing, but this is only meant as a general guide and not a rule. The lower the cage is, the better it will shift. While you’re in this position, take a quick look at the curvature of the large chainring and the outer derailleur cage, to make sure no part of the cage is rubbing on the chainring.
Angle Adjustment
The derailleur angle is set by looking down from above. This can be tricky and requires some patience, as the shape of the derailleur cage is often not straight. You’ll want to imagine a centerline in the middle of the cage, which should line up with the center line of your frame. Once the angle is correct, you can completely tighten the positioning clamp.
Limit Screws
There are two gear limit screws. On older derailleurs the low-gear limit is closest to the frame, but some newer models have reversed the screw’s positioning.
Low Gear Limit
To adjust the low-gear limit, first make sure your chain is shifted to the largest sprocket in the rear, and the smallest sprocket in the front. The low-gear limit stop stops the derailleur from shifting past the smallest chainwheel and throwing the chain onto the bottom bracket shell. If it is too loose, the chain will fall off when you downshift to the small chainring. If it is too tight, it might not shift down at all. Ideally, you want to set up the inner plate so that it barely clears the chain in the lowest gear. However, triple chainrings like this one sometimes require a tiny bit of extra spacing.
High Gear Limit
To adjust the high-gear limit, shift the chain into your highest gear, that is, smallest sprocket in the rear, and the largest sprocket in the front. The high-gear limit prevents the chain from shifting past the largest chainwheel and throwing the chain out into your pedals. Ideally you want the cage to stop just after it clears the chain on the large chainring.
Shifting Adjustments
Now that both limit screws are set up, shift back to the largest sprocket in the rear, and the smallest in the front. Make sure your front shifter is in the lowest gear position, and pull the shift cable to eliminate any extra slack, before tightening the cable bolt.
Shift the front derailleur to the middle gear, and run through the entire range of rear sprockets to make sure the chain does not rub on either side of the front derailleur cage. If it does rub, you can adjust the trim by tweaking the barrel adjuster on your front shift lever. If you have an older friction shifter, often you will have to manually adjust the trim while riding.
This tutorial was based on the most common type of drivetrain, and assumes that you are using the components your derailleur was designed for. If you have a customized set of chainrings and/or derailleurs, you may need to try some different techniques, or even take your bike into a shop for further adjustment.
Related Links
- Jim Langley: Front Derailleur Adjustment
- Park Tool: Front Derailleur Adjustment
- Sheldon Brown: Front Derailer Adjustment
- Utah Mountain Biking: Tuning the Front Derailleur
- Bicycle Torque Specifications
Recommended Tools
- Park Tool HXS-1.2 Hex Wrench Set
- Park Tool Wrench Combo Set
- Tri-Flow Superior Lube
- Park Tool SA-3 Heavy Duty Shop Apron
- Park Tool SK-3 Starter Mechanic Tool Kit
- Park Tool PK-3 Professional Tool Kit
Categories
Discuss this topic in the Bicycle Repairs and Mechanics Forum
Catastrophic bicycle failures
Latest post 1 day agoAs some of you know, I bought a new bicycle that failed catastrophically within 3 days.. ​The gears were slipping and skipping right from day zero. It’s a 3 x 8 setup, and the shop mechanic claimed the manufacturer had mistakenly installed a 7-speed rear derailleur instead of an 8-speed. Whether that's true or not, he eventually swapped it out for a new 8-speed derailleur after my complaints....
Read moreFreehub replacement sealed bearing wheel
Latest post 2 weeks agoI have a Bontrager Race wheel with sealed bearings. While I have a lot of experience with wheels that have loose bearings, I don't have much with wheels that have sealed bearings. So here is my question; how do I get the axle out and the freehub off? Once the axle nuts were off, unlike a wheel with loose bearings, the axle itself still feels rigidly in place. I've watched some youtube videos ...
Read moreShimano RevoShift upgrade
Latest post 3 weeks agoHello. I bought a 2003 Raleigh SC40 recently. It is in very good shape but does show its age in areas. One is the 3x8 Shimano RevoShift twist shifters. They work just fine but are cosmetically challenged. The right rear shifter plastic cover has broken. I am inclined to replace both with new Shimano twist shifters. Hoping for suggestions, recommendations and cautions. Thanks for the help. ...
Read moreSram Transmission derailleur possibly dead?
Latest post 3 weeks agoI have a bike in with an unresponsive transmission derailleur. Customer said it was hit with a stick that went into the spokes. There's no obvious damage other than wear and tear scuff marks. The battery is good and tested with the dropper. The shifter is good and working. The button on the derailleur does nothing. Single click, double clicking and holding the button. no response, no servo buzz,...
Read moreSpecialized bicycle post issue
Latest post 1 month agoHi folks - this is my first post! The seat post on my year old Roll 3.0 is doing something annoying. It has a bit of play around the shiny collar just above the post clamp (see photo). I was told there is a plastic sheathing inside. Can this be fixed or is the seat post all one assembly? IMG_3153.jpeg (Size: 58.61 KB / Downloads: 722) ...
Read morePhilodo H8 5000W
Latest post 1 month agoHave a out 300 miles on a Philodo H8 5000W. A couple of times, after turning it on, it flashed "12" for a few seconds. Anyone have a clue?...
Read moreAxle keeps slipping on applying force/climbing hills..
Latest post 2 months agoMy friend is having this issue where the axle keeps slipping in the rear dropouts and hit the chain stay on the non-drive side. IMG-20260418-WA0021.jpg (Size: 82.12 KB / Downloads: 87) This usually happens when a lot of force (climbing on a high gear or standing to sprint) is applied. It’s worse when the bicycle is loaded up with camping gear on the rear rack. Things tried th...
Read moresuspicious broken part after service--is this legit?
Latest post 2 months agoHey all, I'd love some feedback on a repair issue. I just got the brakes bled and the first ride after was fine. But after one week of sitting idle, I took it out and the rear brake was suddenly making a horrible loud screeching noise when applied. Took it back to the shop and the mechanic showed how the two halves of the brake were not perfectly aligned and holding firm and there was oil leakage....
Read morePros & Cons of presta valve vs schrader valves
Latest post 3 months agoA question I've wanted to ask for a while now. From a personal point of view, what have you found to be the positives and negatives of these two valves? What would your preference be?...
Read more70's=80's Free Spirit Blaze MTN
Latest post 3 months ago70's-80's Free Spirit Blaze MTN 2.JPG (Size: 21.86 KB / Downloads: 15) 3.JPG (Size: 33.89 KB / Downloads: 16) DSCN3722.JPG (Size: 32.65 KB / Downloads: 16) 4.JPG (Size: 56.63 KB / Downloads: 16) I need a front index shift lever or the matched set. Falcon derailleur, 10 speed or whatever is compatible. 7.3mm is the closet spacing measure...
Read moreFront Disc screeching/vibration .. help please :-)
Latest post 3 months agoFront Disc brake(Shimano) makes dreadful noise/vibration just at the ‘bite’ point where it stop the wheel (final 2 or 3 cms of rotation on the rotor ! Only started a month ago No luck in sorting it ! .. have had pads, rotor and caliper all replaced and it makes very little difference (all are clean, aligned and functioning as they should) Absolutely no problem on the rear. Don’t know wh...
Read more2nd hand rad rover repair help needed
Latest post 3 months agoSo I bought this second hand rad rover five power bike it worked for the whole day and the end of the day I thought it died on me but it hasn't been able to start back up please contact me if you think you could help I've done some research and I have no idea what I'm doing I just need some help somebody knows what they're doing to guide me with this please I spent all my money on this I don't hav...
Read moreNeed help with Drivetrain Update
Latest post 5 months agoHello everyone, I'm an older lifelong cyclist that recently had my beloved old yeti mountain bike stolen, and to try and fill that void, I picked up a 2015 Specialized Crosstrail (I'm riding more paved and gravel trails these days, my full-on mountain bike days are over!). The bike was in very good physical condition, apparently very lightly used. I was unable to ride before purchase, but it looke...
Read moreVelowave Ranger break change question
Latest post 5 months agoHello! I tried to change my Velowave ranger e-bike breaks and the lever would not have traction. I researched and learned I needed to bleed the breaks, I tried the top method with the cup with a break bleeding kit. Still had the same issue, I tried to use the syringe at the caliper but the hole was too small for any of the included adapters. Is it just trapped air in the calipers/line that is ca...
Read moreEye to Eye Shock Lengths
Latest post 5 months agoWill my conversion work? I have an old 2014 Giant Trance 1. It is a small frame. It is just a backup bike. It is still fun to ride and works well when a friend is or family member is visiting and bikeless. I hate sending things to the land fill or not being able to keep them repaired and running. I already replaced the fork a couple of years ago. I already found some parts and converted to a ...
Read more
