important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to Overhaul Wheel Bearings

Overhaul a hub, replace and grease the wheel bearings, and adjust the cones.

This tutorial will demonstrate how to grease your wheel bearings. For this job you’ll need some rags, waterproof grease, and a 17mm open-end wrench. You’ll also need a 13mm cone wrench for a front hub, and a 15mm cone wrench for a rear hub. When overhauling a hub, you should always replace the ball bearings. Most front hubs need 10 3/16″ bearings per side, while rear hubs usually need 9 1/4″ bearings.

Dis-Assemble Hub

If you’re overhauling the rear hub, you’ll need to remove the cassette or freewheel before you begin. Carefully remove any seals that may be protecting the cone and locknut.

Place the wheel on its side and slide a cone wrench onto the cone flats, and then loosen the left, or non-drive side locknut by turning it counter-clockwise against the cone wrench. Completely un-thread and remove the cone and locknut, and then slide the axle out from the right side of the hub.

Clean Hub Parts

Clean all of the old grease off of the axle and cones and remove all of the bearings from both sides, making sure to count how many you take out. Then clean the inside of the hub and carefully inspect both the cones and the inner bearing races. If there is any damage such as pitting then the cone and/or hub should be replaced.

Grease Hub and Bearings

Apply a generous layer of grease to both of the hub’s bearing races. Then carefully insert all of the new bearings by pushing them down in the grease. When all of the bearings are installed, there should be about half a bearing space left. Cover all of the bearings with a layer of grease and lightly grease the axle threads.

Re-Assemble Hub

Once the bearings are installed on both sides, carefully slide the axle into hub, making sure the bearings stay in place. Thread the left side cone, washer (if any) and locknut all the way on finger tight.

Adjust Cone and Locknut

Now lay the wheel back on its side and place the cone wrench on the cone. Tighten the locknut against the cone and check to make sure there is no play in the hub, and that the wheel spins freely. You may have to loosen the locknut and repeat the procedure many times before it is correct. Quick release mechanisms tighten the cones slightly, so if you have a quick release axle, you’ll have to leave a slight bit of play in the hub.

Re-install any seals and then put the wheel back on your bike. Finally, check the adjustment again by moving the wheel side to side at the rim. Again, there shouldn’t be play in the wheel, and it should spin smoothly.

Related Links

Recommended Tools

Categories

Discuss this topic in the Bicycle Repairs and Mechanics Forum

I'm slowly eliminated all LBSes in my area as options for servicing, LOL. The latest one has been struck off my list after watching, pained, their approach to removing the axle end caps from a hub with cartridge bearings. Suffice to say, I finally ordered a blind bearing puller kit and a bearing press kit. If you want something done properly, you have to do it yourself! Have you bought any nic...

Read more

Hi Ive joined to specifically ask about a problem which may have been covered before Im sure. My right pedal broke so I had to replace it. Then had issues getting the new pedal to go on straight so I was riding with it slightly at a bend. But then it just came loose and fell off. Problem is now the thread seems busted and the pedal just slots in with no screwing needed because the hole is enlar...

Read more

Trek domane tyre

Latest post 4 days ago

Hi I have a trek domane 2.3, and I have changed the rear tyre to 28 (it was 25 originally) The tyre rubs with the brake arm (v brake), I fear it doesn’t seem to be compatible Is there any way to adjust the position of the brake arm? I just need it to ne around 2mm higher Thanks...

Read more

Modern rims crack at spoke holes

Latest post 4 days ago

Recently, I was in one of the local bike shops. Someone had brought a bike back to have the back wheel re-trued. There were actually cracks in the rim, originating from the spoke holes. I have had the same problem with my bike. In past decades you could buy a bike, and the wheels were strong. With modern rims, the aluminum is getting thinner and thinner. Now the rims crack. With heavy riders, a...

Read more

Cup and cone hubs have long been considered simple, durable, easily maintained, and reliable. Having messed around with a couple of older hubs tonight, I ended up looking at my sealed-bearing hubs with increased fondness. I'm wondering what other people think. Should we old farts just accept that modern hubs with cartridge bearings are the way forward?...

Read more

Falling back

Latest post 4 days ago

In December of 2009 I had a first generation carbon fiber fork break on my road bike and it dropped me right on my forehead. This gave me a very serious concussion and both ER doctors and most neurologists do not take them serious. So it took about two years of my slowly dying since I couldn't even remember to eat before my Cop friend took me to a proper neurologist who diagnosed it as a concussio...

Read more

Derailluer Hanger Alignment Tool

Latest post 4 days ago

I cannot express enough about the importance of this tool when having to deal with multi speed bicycles. I have been in the bicycle biz in one fashion or the other for over 30 years. Have sold many new bicycles and 90% have been out of wack fresh from the box. With used bikes crossing your path you should just expect it to be bad. And never string new cables without checking the hanger first, ever...

Read more

Hey guys, First post here. I've tried searching, but I don't know what you call this. I have a vintage Schwinn Passage that I picked up a few months ago. At first it worked well, but recently it's been giving me trouble. When I shift, the chain pops into the higher (larger) gear, but then sits on top of the chain ring. What ends up happening is that the chainring will keep turning, and eve...

Read more

Went to fix the slow leak on my gravel bike's rear tyre. Found the culprit: a small cut near the middle of the tyre. The good news is it gave me an excuse to order a pair of Panaracer 43c semi-slick GravelKings (most of my local rides are more road-focused) to try out. Meanwhile, I was considering ye olde vulcanised patch repair to the inside of the tyre and superglue to the outside, but I'm thi...

Read more

I shipped my Dawes Super Galaxy home and have just had an unfortunate experience of not being able to re-attach my left Shimano M324 pedal. It looks threaded, but I still have hopes as I think it's only the top couple of rings on the inside. [attachment=5341] From what I can tell the pedal thread is fine. I know there are tools out there to fix a thread. I'm hoping that mine is not so bad that...

Read more

I bought this Vilano Hybrid in 2020 as my “old person’s Chinese Cheapie”. It was - (and is) - FAR from equaling the “serious” bikes that I owned back in the 1990’s. The first Trek I had was a gorgeous blue road bike - worthy of all the gawkers it inspired. My Klein Pro Race MTB was the finest all-round “terrain-chewing animal” I ever mounted. It never failed. It never said...

Read more

Crankarm for Diamondback

Latest post 3 weeks ago

Will a FC-CT93 fit a FC-TY40 crank arm...

Read more

I am heavier than many cyclists. I ride longer distances then many cyclists. A lot of my riding is on rough tracks. While riding my 29 inch mountain bike, spokes broke in the back wheel. https://forums.bikeride.com/thread-8373.html I replaced them with 3 mm spokes. Not long after, cracks formed in the aluminum rim in two places. It became obvious, I could not go on repairing this wheel. I came...

Read more

New Wheel Question

Latest post 4 weeks ago

I just ordered and received new wheels for my bike. Both the old and new are TLR, but I run with tubes. On my old rim, tape is installed. So…when I ordered the new wheels, I also ordered tape. Today, when the new wheels arrived, I noticed that both included a plastic (?) rim strip. I installed the strip on both rims, which gets me to my question…. Do I also need the rim tape? I would think not...

Read more

New Wheel Question

Latest post 4 weeks ago

I just ordered and received new wheels for my bike. Both the old and new are TLR, but I run with tubes. On my old rim, tape is installed. So…when I ordered the new wheels, I also ordered tape. Today, when the new wheels arrived, I noticed that both included a plastic (?) rim strip. I installed the strip on both rims, which gets me to my question…. Do I also need the rim tape? I would think not...

Read more