How to Lubricate Brake and Shift Cables
Cable lubrication is recommended, especially if you ride in the rain or have old cable housings.
Most brake and shift cables these days have a plastic lining built into the housing, therefore eliminating the need for lubrication. However, if you ride a lot in wet weather, or have an older bike without the plastic lining, you’ll want to lubricate the cables to prevent rust. I personally believe that well-lubricated cables also improve braking and shifting.
Lubricant
I use Tri-flow to lubricate cables, as it is very effective at distributing itself evenly, and lasts a long time. Most bike shops carry it, or they may have a similar product that will work just as well. Make sure you shake the bottle before use, and have a rag handy to wipe off any excess.
Brake Cable Lubrication
Most brake and derailleur systems have some sort of quick release system that allow you to release the cable from it’s stop. Here it is demonstrated on a cantilever brake, but other systems like sidepull, U-brakes, and V-brakes have similar quick release mechanisms.
Once the brake is released, compress the lever, pull on the housing, and slide it through the barrel adjuster until the inner wire is exposed. Now carefully squeeze a few drops of oil onto the inner cable just above where it runs down into the housing. If the cable is vertical, the oil will penetrate the housing on its own.
Slide the cable housing back into the barrel adjuster and re-connect the brake.
Shifter Cable Lubrication
Rear Shift Cable
To lube the rear shift cable, first shift the gears until the chain is on the largest sprocket, and then stop the wheel from rotating.
With the freewheel stopped from moving, shift your shifter all the way in the opposite direction, as if you were going to shift to the smallest sprocket. The rear derailleur should now be stuck on the largest sprocket, which will give you enough slack to fully release the cable from the frame. Pull the upper section of the outer cable down leaving a section of inner cable exposed. Lube the cable the same way as the brake cable, and then reconnect the outer housing.
Now pull the lower section of housing free from the frame, and slide it away from the derailleur. Repeat the lubrication process and reconnect the housing. Don’t forget to move your rear shifter back to the largest sprocket before rotating the rear wheel.
Front Shift Cable
To lube the front shift cable, shift the front derailleur to the largest sprocket, and then stop the crank from rotating and move the shift lever all the way in the opposite direction. Disconnect and lube the upper housing of the front shift cable the same way as the rear. Reconnect the cable and once again make sure to shift the lever back where it was before rotating the crank.
Related Links
Recommended Tools
- Tri-Flow Superior Lube
- Hozan 4th Hand Cable Puller
- Park Tool HXS-1.2 Hex Wrench Set
- Park Tool Wrench Combo Set
- Park Tool SK-3 Starter Mechanic Tool Kit
- Park Tool PK-3 Professional Tool Kit
Categories
Discuss this topic in the Bicycle Repairs and Mechanics Forum
Cassette shifting Problem
Latest post 3 hours agoI just replace the 10 speed cassette on my Mountain bike. I decided to go for a largest cog with more teeth for an easier ride uphill.. I increased from 38T to 42T. I also replaced the chain and chainrings at the same time. When the bike was on the stand it ran through the gears well. I had the following problem when out riding. I had just ridden up a steep hill on the 22T chain ring and the ...
Read moreWhat are the pros and cons of using a 26" tube on a 29" wheel?
Latest post 16 hours agoI recently upgraded after 20+ years from a 26" to a 29" wheel. Consequently, I have 8 new 26" tubes in my garage. I ride 90% mountain biking. Curious. Have you ever fitted a 26" tube on a 29"? What was the result? And would you recommend it?...
Read moreVariation in Conti GP5000 sizing?
Latest post 2 days agoI must have fitted 3 or 4 pairs of 25mm Continental GP5000 tires without any trouble whatsoever. On different brands of 622x15c rim, they went on without struggle or complaint. Older GP4000 also went on without trouble. However, the most recent set, bought a month ago, are probably the worst I've ever had in terms of the challenge I had to get them fitted. Has anyone else found such a big differ...
Read moreHow often check or change mechanical disc brakes
Latest post 2 weeks agoI'm curious—how often or after how many miles do people typically check or change their mechanical disc brake pads? I've been bikepacking for a while but never really followed a maintenance schedule. A few weeks ago, I took my bike to a mechanic because I heard some noise. The mechanic did a quick overhaul, and I was sent on my way. However, a few weeks later, while descending steep hills, I s...
Read morePros & Cons of presta valve vs schrader valves
Latest post 2 weeks agoA question I've wanted to ask for a while now. From a personal point of view, what have you found to be the positives and negatives of these two valves? What would your preference be?...
Read moreGrip Shifters
Latest post 2 weeks agoCurrently renovating a child's bike. It has 24 inch wheels and is a suitable size for a 7-10 year old. Anyway it has grip shifters. it is a six speed with three chain rings on the front derailleur. On the rear derailleur the shifter does not appear to move the gear cable at all when shifting from 6 to 5 and 5 to 4. I am actually holding the cable with my finger and thumb against the cable cas...
Read moreLeft a bike outside on the balcony for couple of months. How to get rid of the rust?
Latest post 3 weeks agop6i6rfpm1ip41 (1).jpg (Size: 82.1 KB / Downloads: 539) Is there a way to get rid of that rust or do I need to replace certain components? More pics...
Read more9 speed chain on 8 speed bike
Latest post 3 weeks agoAll of my bikes are 7 or 8 speed and sometime in the past I bought a 9 speed chain for some unremembered reason. is there any reason not to use it on an 8 speed bike?...
Read moreRusty chain inspite of cleaning,lubing
Latest post 3 weeks agoHello, I was going to ask this question in @Flowrider’s post, but since this is a slightly different issue, I decided to start a new post. https://forums.bikeride.com/thread-9267.html I’m nowhere near the ocean, so salt-related rusting isn’t a concern. I’m currently in the ninth month of a long bikepacking trip, and sometimes I stay in one place for a week or longer. During this week or ...
Read moreColnago restoration
Latest post 1 month agoHi everyone. A bit repetitive from my intro in GF, but this is the correct section for this post. I’m new to vintage bikes, but I’ve been eyeing a vintage Colnago to restore for a long time. Finally found one and the timing was right to pull the trigger. I’m still trying to identify the exact year, but from my research it’s 1991-1993 Colnago Super PiU. Mostly original, I think, apart from ...
Read moreColumbia 3 wheel differential
Latest post 2 months agoHello everyone and thank you so much for having me! I have an older Columbia 3 wheeler adult tricycle and she has a differential, somewhat like a car. I wanted to open up the differential for cleaning and oiling but cannot find any info on her, as to how much oil to add, and where the oil fill point is. Can anyone help me in this endeavor? I'd really love to get her going but don't want to ris...
Read moreFront derailer not moving
Latest post 2 months agoHi, I been upgrading my old bike with new brake and shift cables. I got my brakes working and now trying to get my shift cables working. I was able to install new shift cable, I made sure to hold the cable tight and tighten the Bolt to keep in place. But it doesn't move the derailer at all when shifting. I have a feeling it's a simple fix that I'm missing something. I thought it might be the new ...
Read moreWhat are the best cost effective ways to prevent chain rust?
Latest post 2 months agoI live 5 km from the ocean (not sure if that's relevant), and I pretty much only mountain bike. After every ride, I hose down and clean my bike. I wipe them down with a cloth. After a few days, the ones not ridden have what looks like surface rust appear on the chain. Do you have any cost-effective remedies to solve this issue?...
Read moreHow to deal with rusty chain
Latest post 2 months agoThe best thing is not to let your chain get rusty in the first place. Chains for most 6,7,8 speed bikes can be had for $15 to $20 all day long. For me my first choice is to just replace it and the reason is simple. If finished it does not meet the level of 95%+ perfect it will get replaced. If the chain you are trying to save does not have a quik link then that is an extra cost to figure...
Read moreRear v-brake repair
Latest post 3 months agoHi everyone, I'm new here and I've been trying to avoid taking my bike to a mechanic and save some money. I succesfully fixed my front but struggle with the rear, I got new brakes for the rear. I notice i think it might be the housing causing the noodle to be off centered and making the left brake pad to close to the rim. Any help would be greatly appreciated, thanks!! My next project is to attemp...
Read more
