important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to Adjust Your Rear Derailleur

Applies to most 3-chainring derailleur systems. Adjust Front Derailleur

Adjusting your rear derailleur can be frustrating. I’m hoping that this tutorial will help you understand how each component of your derailleur works, and how to set up and adjust it properly. Once your derailleur is set up correctly, most future adjustments can be done by hand. Let’s get started!

Required Tools

You’ll need a rag, a phillips screwdriver, a 5mm allen wrench, and a light lubricant like Triflow or Phil Wood Tenacious oil.

Rear Derailleur Components

Derailer, Not Derailleur! (Sheldon Brown)

How They Work

Almost all modern derailleurs function the same basic way. They are designed to move (or derail) the chain from one sprocket to the next. The upper guide pulley (or jockey pulley) moves the chain in both directions. For instance, when you want to climb a hill, you shift down to a lower gear. This pulls the shift cable and forces the guide pulley to change to a bigger sprocket. When you want to go faster, you adjust the shifter to a higher gear. This releases shift cable tension and allows the derailleur springs to pull the guide pulley back down to a smaller gear. Each time you shift gears, the length of chain changes. The lower tension pulley is spring-loaded to take up this slack.

Limit Screws

There are 3 adjustment screws – the B-Screw (B-tension adjustment), the H-Screw (high gear limit stop) and the L-Screw (low gear limit stop). Adjustments on these screws should always be made in 1/4 turn increments.

B-Tension Adjustment

The B-Screw controls the derailleur body’s angle in relation to the sprocket-set. Shift down to the largest sprocket and check the distance between the guide pulley and the large sprocket. If the guide pulley is rubbing on the sprocket, tighten the B-screw clockwise to increase tension and move the pulley away from the sprocket. If there is a large gap between the pulley and sprocket, loosen the B-screw until the pulley rubs the sprocket, and then tighten it until it just clears.

High Gear Limit Stop

The H-Limit screw high gear limit stop prevents the guide pulley from shifting any further past the highest gear and into the axle. In order to adjust it properly there must be no tension on the lower inner cable. If you feel tension, loosen the cable adjuster until there is none. Now check from behind how the chain is riding on the smallest sprocket. If it looks like it wants ride off into the axle, tighten the H-screw clockwise until it lines up. If it looks like it is rubbing on the next gear, loosen the screw until the chain is nicely centered on the sprocket. Now re-adjust the cable tension until the derailleur shifts smoothly down to the next gear.

Low Gear Limit Stop

The L-Limit screw prevents the guide pulley from shifting any further past the lowest gear and into the wheel spokes. Shift down to the lowest gear, step behind the bike, and check how the chain rides on the sprocket. If it looks like it wants to ride into the spokes, tighten the L-screw clockwise until it is centered on the sprocket. If it looks like it wants to shift down, loosen the screw until it lines up. As an extra precaution you can use your thumb to gently push the derailleur body and make sure the chain will not run into the spokes, as this could obviously have a nasty effect on both you and your bike.

Cable Adjustment

The cable tension adjuster defines how far up or down the derailleur moves. Step back so you can see the chain and sprocket alignment, and then through the gears in both directions, first shifting up two and down one, and then down two and up one. The chain should look centered on each sprocket. If it is rubbing on a larger gear it means there is too much tension on the cable. Loosen the tension by turning the adjuster clockwise. If it wants to jump down to a smaller gear it needs more tension. Increase the tension by turning the adjuster counter-clockwise.

You can also use sound to check the adjustment. There is always a base-level of noise that can be heard in every gear. This noise will increase in a slightly different way depending on which way the tension is out of adjustment. If there is too much tension you will hear a metallic rubbing sound, but if there is too little tension you will hear a clicking noise as the chain tries to jump to a smaller sprocket. There is usually a cable tension adjuster on your shift lever. With practice you will be able to make small cable tension adjustments while you are riding.

Lubrication

Now that the derailleur is adjusted, always apply a drop of lubrication to the derailleur’s many moving parts. This will help prevent wear from dirt and rust, and it will keep your gears shifting smoothly. Wipe away any excess lube and take your bike for a test ride to make sure all the gears are working smoothly.

That concludes our tutorial on rear derailleur adjustments… have fun!

By Alex Ramon

A bicycle geek since early childhood, spent his twenties as a mechanic in bike shops. His passions include flatland BMX, unicycles, cycle touring, mountain biking and road riding.

Recommended Tools

Discuss this topic in the Bicycle Repairs and Mechanics Forum

suspicious broken part after service--is this legit?

Pros & Cons of presta valve vs schrader valves

70's=80's Free Spirit Blaze MTN

Front Disc screeching/vibration .. help please :-)

2nd hand rad rover repair help needed

Axle keeps slipping on applying force/climbing hills..

Need help with Drivetrain Update

Latest post 3 months ago

Hello everyone, I'm an older lifelong cyclist that recently had my beloved old yeti mountain bike stolen, and to try and fill that void, I picked up a 2015 Specialized Crosstrail (I'm riding more paved and gravel trails these days, my full-on mountain bike days are over!). The bike was in very good physical condition, apparently very lightly used. I was unable to ride before purchase, but it looke...

Velowave Ranger break change question

Latest post 3 months ago

Hello! I tried to change my Velowave ranger e-bike breaks and the lever would not have traction. I researched and learned I needed to bleed the breaks, I tried the top method with the cup with a break bleeding kit. Still had the same issue, I tried to use the syringe at the caliper but the hole was too small for any of the included adapters. Is it just trapped air in the calipers/line that is ca...

Eye to Eye Shock Lengths

Latest post 3 months ago

Will my conversion work? I have an old 2014 Giant Trance 1. It is a small frame. It is just a backup bike. It is still fun to ride and works well when a friend is or family member is visiting and bikeless. I hate sending things to the land fill or not being able to keep them repaired and running. I already replaced the fork a couple of years ago. I already found some parts and converted to a ...

Shimano law suit

Latest post 3 months ago

Remember the Shimano law suit? Fortunately I had the"good model series" Thousands of riders trusted these components without a second thought. Now, the story has taken a serious turn. Shimano has agreed to pay an $11.5 million penalty after US regulators found the company failed to report a major defect in its 11 speed road cranksets on time. According to the CPSC, Shimano had received thou...

Question regarding rear hub replacement for possible out of production bike?

Latest post 4 months ago

Hi there, I have a question in regards to either finding a replacement hub for my rear Mountain Bike or just replacing the whole wheel entirely. However when I went to a local bicycle shop (in China, that is so there are language barriers to keep in mind), upon inspection they claimed that the bicycle was too old to accept the replacement of their modern parts, which I honestly find hard to believ...

Need suntour derailleur replacement

Latest post 4 months ago

My sensation crossroads cruz needs a rear derailleur. I need to verify which shimano part and shifter will work. Thanks Bob...

Inner side tube punctures

Latest post 4 months ago

I haven't been riding a bike for about two years, before that I was riding it extensively for about 5 or more years. It is a 26 inch mountain bike (if that matters at all). The bike was just staying on flat tires for these two years. After i decided to put the bike to life again so to speak I started to get inner tube punctures (punctures on a tube from the inner side, the side not facing the road...

How to adjust shock preload?

Latest post 4 months ago

These are Noleen NR-1 shocks on an old Girvin ProFlex MTB. How do I get a grip on the preload adjuster? There is very little surface area & there are no notches for a typical spanner & a pipe wrench, vice grips, etc. which are sure to mar the springs if I can even get them in there to grip it. The working space on the fork shock is especially tight. See attachment photos. Thanks! ...