How to Overhaul a Threaded Headset
Overhaul your headset at least once a year to check for wear and re-grease the ball bearings.
If you ride your bike a lot, you should overhaul your headset at least once a year to check for wear and to make sure the bearings have enough grease.
Required Tools
For this tutorial, you’ll need some waterproof grease, an old toothbrush and some cleaning solvent. If you have an older 1″ headset, you’ll need a set of 32mm spanner wrenches. Larger 1 1/8″ headsets usually require a set of 36mm spanner wrenches.
Brake Cable, Wheel and Stem Removal
Before you begin, you’ll need to disconnect the front brake and remove the brake cable from the lever. You’ll also need to remove the front wheel. To remove the stem, simply loosen the stem’s tightening bolt far enough so you can give it a light tap with a hammer. This will knock the inner wedge loose and allow the stem to slide up out of the fork.
Headset Disassembly
Now loosen and remove the locknut. Holding the fork in place with one hand, remove any spacers and unthread the adjusting race. Make sure to note how many spacers there are, and what order they came off. Gently slide the fork down and out of the frame. Make sure to make a note of which way the bearing races are facing before you remove them.
Headset Cleaning
Wipe clean all of the bearing races located on both the frame and fork as well as the upper threaded race. Inspect all four of the bearing races to make sure they are not grooved or pitted. If so you will likely have to replace the entire headset unit.
Thouroughly clean the ball bearing cages with your toothbrush and solvent. Then wipe them dry with a clean rag, and set them aside to air-dry. Inspect the ball cages to make sure they aren’t bent or worn. You can replace the cages without replacing the entire headset, but you’ll have to bring the old set to your local bike shop for proper sizing.
Headset Greasing
If all of your parts are ok, apply a layer of grease to all of the bearing races. Then install the ball cages the same way they came out and add another layer of grease on top of them.
Headset Assembly
Once the bearings are in place and fully greased, carefully slide the fork back into the frame and finger-tighten the adjusting race. Wipe off any excess grease that may have squirted out the sides. Slide the spacers back on and thread the locknut on finger tight.
Headset Adjustment
To adjust the headset, hold the lower adjusting race with a spanner wrench and use a second spanner to tighten locknut against the adjusting race.
To test the adjustment, check that the headset turns freely and check for play by rocking the fork back and forth in the frame. Re-adjust as needed until the bars spin freely and have no play.
Brake Cable, Wheel and Stem Installation
Reinstall the front wheel. Before reinstalling the stem, coat the shaft and wedge with a thin layer of grease. Then reinstall and tighten the handlebar stem, and reconnect the front brake.
Final Adjustment
Then re-test the headset adjustment by making sure the bars spin freely, and using your front brake, rock the bike back and forth to double check there is no play in the headset.
Related Links
Recommended Tools
- Park Tool HCW-15 Dual-Size Headset Wrench
- Park Tool HW-2 Headset Locknut Wrench (32mm and 36mm)
- Park Tool AWS-1 3-Way Hex Wrench
- Park Tool PAW-12 Adjustable Wrench
- Super Lube White Grease Tube
- Finish Line Grease Gun
Categories
Discuss this topic in the Bicycle Repairs and Mechanics Forum
Catastrophic bicycle failures
Latest post 20 hours agoAs some of you know, I bought a new bicycle that failed catastrophically within 3 days.. ​The gears were slipping and skipping right from day zero. It’s a 3 x 8 setup, and the shop mechanic claimed the manufacturer had mistakenly installed a 7-speed rear derailleur instead of an 8-speed. Whether that's true or not, he eventually swapped it out for a new 8-speed derailleur after my complaints....
Read moreNeed suntour derailleur replacement
Latest post 6 days agoMy sensation crossroads cruz needs a rear derailleur. I need to verify which shimano part and shifter will work. Thanks Bob...
Read morePros & Cons of presta valve vs schrader valves
Latest post 1 week agoA question I've wanted to ask for a while now. From a personal point of view, what have you found to be the positives and negatives of these two valves? What would your preference be?...
Read moreHow to clean a bike for beginners (Foxter mtb 29er)
Latest post 2 weeks agoHello. I'm a beginner and I want to know how to clean a bike properly, do diagnostics test to make sure the group set is proper. And make sure my bike is pristine before and after every ride. Bonus question, do you have any videos on foxter mtb 29ers on how to disassemble and reassemble parts of the bike?...
Read moreFreehub replacement sealed bearing wheel
Latest post 4 weeks agoI have a Bontrager Race wheel with sealed bearings. While I have a lot of experience with wheels that have loose bearings, I don't have much with wheels that have sealed bearings. So here is my question; how do I get the axle out and the freehub off? Once the axle nuts were off, unlike a wheel with loose bearings, the axle itself still feels rigidly in place. I've watched some youtube videos ...
Read moreShimano RevoShift upgrade
Latest post 1 month agoHello. I bought a 2003 Raleigh SC40 recently. It is in very good shape but does show its age in areas. One is the 3x8 Shimano RevoShift twist shifters. They work just fine but are cosmetically challenged. The right rear shifter plastic cover has broken. I am inclined to replace both with new Shimano twist shifters. Hoping for suggestions, recommendations and cautions. Thanks for the help. ...
Read moreSram Transmission derailleur possibly dead?
Latest post 1 month agoI have a bike in with an unresponsive transmission derailleur. Customer said it was hit with a stick that went into the spokes. There's no obvious damage other than wear and tear scuff marks. The battery is good and tested with the dropper. The shifter is good and working. The button on the derailleur does nothing. Single click, double clicking and holding the button. no response, no servo buzz,...
Read moreSpecialized bicycle post issue
Latest post 2 months agoHi folks - this is my first post! The seat post on my year old Roll 3.0 is doing something annoying. It has a bit of play around the shiny collar just above the post clamp (see photo). I was told there is a plastic sheathing inside. Can this be fixed or is the seat post all one assembly? IMG_3153.jpeg (Size: 58.61 KB / Downloads: 730) ...
Read morePhilodo H8 5000W
Latest post 2 months agoHave a out 300 miles on a Philodo H8 5000W. A couple of times, after turning it on, it flashed "12" for a few seconds. Anyone have a clue?...
Read moreAxle keeps slipping on applying force/climbing hills..
Latest post 2 months agoMy friend is having this issue where the axle keeps slipping in the rear dropouts and hit the chain stay on the non-drive side. IMG-20260418-WA0021.jpg (Size: 82.12 KB / Downloads: 88) This usually happens when a lot of force (climbing on a high gear or standing to sprint) is applied. It’s worse when the bicycle is loaded up with camping gear on the rear rack. Things tried th...
Read moresuspicious broken part after service--is this legit?
Latest post 3 months agoHey all, I'd love some feedback on a repair issue. I just got the brakes bled and the first ride after was fine. But after one week of sitting idle, I took it out and the rear brake was suddenly making a horrible loud screeching noise when applied. Took it back to the shop and the mechanic showed how the two halves of the brake were not perfectly aligned and holding firm and there was oil leakage....
Read more70's=80's Free Spirit Blaze MTN
Latest post 3 months ago70's-80's Free Spirit Blaze MTN 2.JPG (Size: 21.86 KB / Downloads: 22) 3.JPG (Size: 33.89 KB / Downloads: 22) DSCN3722.JPG (Size: 32.65 KB / Downloads: 20) 4.JPG (Size: 56.63 KB / Downloads: 21) I need a front index shift lever or the matched set. Falcon derailleur, 10 speed or whatever is compatible. 7.3mm is the closet spacing measure...
Read moreFront Disc screeching/vibration .. help please :-)
Latest post 3 months agoFront Disc brake(Shimano) makes dreadful noise/vibration just at the ‘bite’ point where it stop the wheel (final 2 or 3 cms of rotation on the rotor ! Only started a month ago No luck in sorting it ! .. have had pads, rotor and caliper all replaced and it makes very little difference (all are clean, aligned and functioning as they should) Absolutely no problem on the rear. Don’t know wh...
Read more2nd hand rad rover repair help needed
Latest post 4 months agoSo I bought this second hand rad rover five power bike it worked for the whole day and the end of the day I thought it died on me but it hasn't been able to start back up please contact me if you think you could help I've done some research and I have no idea what I'm doing I just need some help somebody knows what they're doing to guide me with this please I spent all my money on this I don't hav...
Read moreNeed help with Drivetrain Update
Latest post 6 months agoHello everyone, I'm an older lifelong cyclist that recently had my beloved old yeti mountain bike stolen, and to try and fill that void, I picked up a 2015 Specialized Crosstrail (I'm riding more paved and gravel trails these days, my full-on mountain bike days are over!). The bike was in very good physical condition, apparently very lightly used. I was unable to ride before purchase, but it looke...
Read more
